Directive 2009/45/EC of the European Parliament and of the Council of 6 May 2009 on safety rules and standards for passenger ships (Recast) (Text with EEA relevance )

25.6.2009

EN

Official Journal of the European Union

L 163/1

(1)

Council Directive 98/18/EC of 17 March 1998 on safety rules and standards for passenger ships (3) has been substantially amended several times (4). Since further amendments are to be made, it should be recast in the interests of clarity.

(2)

Within the framework of the common transport policy measures must be adopted to enhance safety in maritime transport.

(3)

The Community is seriously concerned about shipping casualties in which passenger ships were involved resulting in a massive loss of life. Persons using passenger ships and high-speed passenger craft throughout the Community have the right to expect and to rely on an appropriate level of safety on board.

(4)

Work equipment and personal protective equipment of workers are not covered by this Directive, because the provisions of Council Directive 89/391/EEC of 12 June 1989 on the introduction of measures to encourage improvements in the safety and health of workers at work (5) and the relevant provisions of its relevant individual directives are applicable to the use of such equipment on passenger ships engaged on domestic voyages.

(5)

The provision of maritime passenger transport services between Member States has already been liberalised by Council Regulation (EEC) No 4055/86 of 22 December 1986 applying the principle of freedom to provide services to maritime transport between Member States and between Member States and third countries (6). The application of the principle of freedom to provide services to maritime transport within Member States (maritime cabotage) has been provided for by Council Regulation (EEC) No 3577/92 (7).

(6)

To attain a high level of safety, and to remove barriers to trade, it is necessary to establish harmonised safety standards at an appropriate level for passenger ships and craft operating domestic services. Standards for vessels operating international voyages are being developed within the International Maritime Organization (IMO). Procedures to request action at the IMO in order to bring the standards for international voyages into line with the standards of this Directive should be available.

(7)

In view, in particular, of the internal market dimension of maritime passenger transport, action at Community level is the only possible way to establish a common level of safety for ships throughout the Community.

(8)

In view of the principle of proportionality, a Directive is the appropriate legal instrument as it provides a framework for a uniform and compulsory application of the safety standards by Member States, while leaving to each Member State the right to decide the implementation tools that best fit its internal system.

(9)

In the interests of improving safety and avoiding distortions of competition the common safety requirements should apply to passenger ships and high-speed passenger craft engaged on domestic voyages in the Community, irrespective of the flag they fly. It is, however, necessary to exclude some categories of ships for which the rules of this Directive are technically unsuitable or economically unviable.

(10)

Passenger ships should be divided into different classes depending upon the range and conditions of the sea areas in which they operate. High-speed passenger craft should be categorised in accordance with the provisions of the High-Speed Craft Code established by the IMO.

(11)

The main reference framework for the safety standards should be the 1974 International Convention for the Safety of Life at Sea (the 1974 SOLAS Convention), as amended, which encompasses internationally agreed standards for passenger ships and high-speed passenger craft engaged on international voyages, as well as appropriate Resolutions adopted by the IMO and other measures complementing and interpreting that Convention.

(12)

The various classes of both new and existing passenger ships require a different approach for establishing safety requirements guaranteeing an equivalent safety level in view of the specific needs and limitations of those various classes. It is appropriate to make distinctions in the safety requirements to be respected as between new and existing ships since imposing the rules for new ships on existing ships would involve such extensive structural changes as to make them economically unviable.

(13)

The financial and technical implications arising from the upgrading of existing ships to the standards provided for by this Directive justify certain transitional periods.

(14)

In view of the substantial differences in the design, construction and use of high-speed passenger craft compared to traditional passenger ships, such craft should be required to respect special rules.

(15)

Shipborne marine equipment, complying with the provisions of Council Directive 96/98/EC of 20 December 1996 on marine equipment (8), when installed on board a passenger ship, should not be subject to additional tests since such equipment is already subject to the standards and procedures of that Directive.

(16)

Directive 2003/25/EC of the European Parliament and of the Council of 14 April 2003 on specific stability requirements for ro-ro passenger ships (9) introduced strengthened stability requirements for ro-ro passenger vessels operating on international services to and from Community ports, and this enhanced measure should also apply to certain categories of such vessels operating on domestic services under the same sea conditions. Failure to apply such stability requirements should be grounds for phasing out ro-ro passenger ships after a certain number of years of operation. In view of the structural modifications that the existing ro-ro passenger ships may need to undergo in order to comply with the specific stability requirements, those requirements should be introduced over a period of years in order to give the part of the industry affected sufficient time to comply: to that end, provision should be made for a phasing-in timetable for existing ships. This phasing-in timetable should not affect the enforcement of the specific stability requirements in the sea areas covered by the Annexes to the Stockholm Agreement of 28 February 1996.

(17)

It is important to apply appropriate measures to ensure access in safe conditions for persons with reduced mobility to passenger ships and high-speed passenger craft operating on domestic services in the Member States.

(18)

Subject to control under the Committee procedure, Member States may adopt additional safety requirements if justified by local circumstances, permit the use of equivalent standards, or adopt exemptions from the provisions of this Directive under certain operating conditions, or adopt safeguard measures in exceptional dangerous circumstances.

(19)

Regulation (EC) No 2099/2002 of the European Parliament and of the Council of 5 November 2002 establishing a Committee on Safe Seas and the Prevention of Pollution from Ships (COSS) (10) centralised the tasks of the committees established under the pertinent Community legislation on maritime safety, the prevention of pollution from ships and the protection of shipboard living and working conditions.

(20)

The measures necessary for the implementation of this Directive should be adopted in accordance with Council Decision 1999/468/EC of 28 June 1999 laying down the procedures for the exercise of implementing powers conferred on the Commission (11).

(21)

In particular, the Commission should be empowered to adapt certain provisions of this Directive, including its Annexes, to take account of developments at international level and specifically amendments to International Conventions. Since those measures are of general scope and are designed to amend non-essential elements of this Directive, they must be adopted in accordance with the regulatory procedure with scrutiny provided for in Article 5a of Decision 1999/468/EC.

(22)

In order to monitor the effective implementation and enforcement of this Directive, surveys should be carried out on new and existing passenger ships and craft. Compliance with this Directive should be certified by or on behalf of the Administration of the flag State.

(23)

In order to ensure full application of this Directive, Member States should lay down a system of penalties for breach of the national provisions adopted pursuant to this Directive and should monitor compliance with the provisions of this Directive on the basis of provisions modelled on those laid down in Council Directive 95/21/EC of 19 June 1995 on port State control of shipping (12).

(24)

The new elements introduced into this Directive only concern the committee procedures. They therefore do not need to be transposed by the Member States.

(25)

This Directive should be without prejudice to the obligations of the Member States relating to the time-limits for transposition into national law and application of the Directives set out in Annex IV, Part B,

(a)

‘International Conventions’ means the 1974 International Convention for the Safety of Life at Sea (the 1974 SOLAS Convention), as amended, and the 1966 International Convention on Load Lines, together with the Protocols and amendments thereto;

(b)

‘Intact Stability Code’ means the ‘Code on Intact Stability for all types of ships covered by IMO Instruments’ contained in IMO Assembly Resolution A.749(18) of 4 November 1993, as amended;

(c)

‘High-Speed Craft Code’ means the ‘International Code for Safety of High-Speed Craft’ contained in IMO Maritime Safety Committee Resolution MSC.36(63) of 20 May 1994, in its up-to-date version;

(d)

‘GMDSS’ means the Global Maritime Distress and Safety System as laid down in Chapter IV of the 1974 SOLAS Convention, as amended;

(e)

‘a passenger ship’ means a ship which carries more than 12 passengers;

(f)

‘ro-ro passenger ship’ means a ship carrying more than 12 passengers, having ro-ro cargo spaces or special category spaces, as defined in Regulation II-2/A/2 contained in Annex I;

(g)

‘high-speed passenger craft’ means a high-speed craft as defined in Regulation X/1 of the 1974 SOLAS Convention, as amended, which carries more than 12 passengers, with the exception of passenger ships engaged on domestic voyages in sea areas of Class B, C or D when:

(h)

‘new ship’ means a ship the keel of which was laid or which was at a similar stage of construction on or after 1 July 1998; a ‘similar stage of construction’ means the stage at which:

(i)

‘existing ship’ means a ship which is not a new ship;

(j)

‘age’ means the age of the ship, expressed in terms of the number of years after the date of its delivery;

(k)

‘passenger’ means every person other than:

(l)

‘length of a ship’, unless expressly provided otherwise, means 96 % of the total length on a water line at 85 % of the least moulded depth measured from the top of the keel, or the length from the fore side of the stem to the axis of the rudder stock on that waterline, if that be greater. In ships designed with a rake of keel the waterline on which this length is measured shall be parallel to the designed waterline;

(m)

‘bow height’ means the bow height defined in Regulation 39 of the 1966 International Convention on Load Lines as the vertical distance at the forward perpendicular between the waterline corresponding to the assigned summer freeboard and the designed trim and the top of the exposed deck at side;

(n)

‘ship with a full deck’ means a ship that is provided with a complete deck, exposed to weather and sea, which has permanent means of closing all openings in the weatherpart thereof and below which all openings in the sides of the ship are fitted with permanent means of at least weathertight closing;

the complete deck may be a watertight deck or equivalent structure consisting of a non-watertight deck completely covered by a weathertight structure of adequate strength to maintain the weathertight integrity and fitted with weathertight closing appliances;

(o)

‘international voyage’ means a voyage by sea from a port of a Member State to a port outside that Member State, or conversely;

(p)

‘domestic voyage’ means a voyage in sea areas from a port of a Member State to the same or another port within that Member State;

(q)

‘sea area’ means an area as established pursuant to Article 4(2);

however, for the application of the provisions on radiocommunication, the definitions of sea areas will be those defined in Regulation 2, Chapter IV of the 1974 SOLAS Convention, as amended;

(r)

‘port area’ means an area other than a sea area, as defined by the Member States, extending to the outermost permanent harbour works forming an integral part of the harbour system, or to the limits defined by natural geographical features protecting an estuary or similar sheltered area;

(s)

‘place of refuge’ means any naturally or artificially sheltered area which may be used as a shelter by a ship or craft under conditions likely to endanger its safety;

(t)

‘Administration of the flag State’ means the competent authorities of the State whose flag the ship or craft is entitled to fly;

(u)

‘host State’ means a Member State to or from whose port(s) a ship or craft, flying a flag other than the flag of that Member State, is carrying out domestic voyages;

(v)

‘recognised organisation’ means an organisation recognised in conformity with Article 4 of Council Directive 94/57/EC of 22 November 1994 on common rules and standards for ship inspection and survey organisations and for the relevant activities of maritime administrations (13);

(w)

‘a mile’ is 1 852 metres;

(x)

‘significant wave height’ means the average height of the highest third of wave heights observed over a given period;

(y)

‘persons with reduced mobility’ means anyone who has a particular difficulty when using public transport, including elderly persons, disabled persons, persons with sensory impairments and wheelchair users, pregnant women and persons accompanying small children.

(a)

new passenger ships;

(b)

existing passenger ships of 24 metres in length and above;

(c)

high-speed passenger craft.

(a)

passenger ships which are:

(b)

high-speed passenger craft which are:

‘Class A’

means a passenger ship engaged on domestic voyages other than voyages covered by Classes B, C and D.

‘Class B’

means a passenger ship engaged on domestic voyages in the course of which it is at no time more than 20 miles from the line of coast, where shipwrecked persons can land, corresponding to the medium tide height.

‘Class C’

means a passenger ship engaged on domestic voyages in sea areas where the probability of exceeding 2,5 metres significant wave height is smaller than 10 % over a one-year period for all-year-round operation, or over a specific restricted period of the year for operation exclusively in such period (e.g. summer period operation), in the course of which it is at no time more than 15 miles from a place of refuge, nor more than 5 miles from the line of coast, where shipwrecked persons can land, corresponding to the medium tide height.

‘Class D’

means a passenger ship engaged on domestic voyages in sea areas where the probability of exceeding 1,5 metres significant wave height is smaller than 10 % over a one-year period for all-year-round operation, or over a specific restricted period of the year for operation exclusively in such period (e.g. summer period operation), in the course of which it is at no time more than 6 miles from a place of refuge, nor more than 3 miles from the line of coast, where shipwrecked persons can land, corresponding to the medium tide height.

(a)

establish, and update when necessary, a list of sea areas under its jurisdiction, delimiting the zones for all-year-round operation and, where appropriate, restricted periodical operation of the classes of ships, using the criteria for classes set out in paragraph 1;

(b)

publish the list in a public database available on the Internet site of the competent maritime authority;

(c)

notify to the Commission the location of such information, and when modifications are made to the list.

(a)

the construction and maintenance of the hull, main and auxiliary machinery, electrical and automatic plants shall comply with the standards specified for classification by the rules of a recognised organisation, or equivalent rules used by an Administration in accordance with Article 14(2) of Directive 94/57/EC;

(b)

the provisions of Chapters IV, including the 1988 GMDSS amendments, V and VI of the 1974 SOLAS Convention, as amended, shall apply;

(c)

the provisions for shipborne navigational equipment of Regulation 12, Chapter V of the 1974 SOLAS Convention, as amended, shall apply. Shipborne navigational equipment, as listed in Annex A.1 to Directive 96/98/EC and complying with the provisions of the latter, shall be considered to be in conformity with the type approval requirements of SOLAS regulation V/12(r), as amended.

(a)

general requirements:

(b)

load line requirements:

(a)

existing passenger ships of Class A shall comply with the regulations for existing passenger ships defined in the 1974 SOLAS Convention, as amended, and with the specific relevant requirements in this Directive; for those regulations for which the 1974 SOLAS Convention, as amended, leaves the interpretation to the discretion of the Administration, the Administration of the flag State shall apply the interpretations as contained in Annex I to this Directive;

(b)

existing passenger ships of Class B shall comply with the specific relevant requirements in this Directive;

(c)

existing passenger ships of Classes C and D shall comply with the specific relevant requirements in this Directive and in respect of matters not covered by such requirements with the rules of the Administration of the flag State; such rules shall provide an equivalent level of safety to that of Chapters II-1 and II-2 of Annex I, while taking into account the specific local operational conditions related to the sea areas in which ships of such classes may operate;

before existing passenger ships of Classes C and D can be engaged on regular domestic voyages in a host State, the Administration of the flag State shall obtain concurrence of the host State on such rules;

(d)

where a Member State is of the view that rules required by the Administration of the host State pursuant to point (c) are unreasonable, it shall immediately notify the Commission thereof; the Commission shall initiate proceedings in order to take a decision in accordance with the procedure referred to in Article 11(2);

(e)

repairs, alterations and modifications of a major character and outfitting related thereto shall be in compliance with the requirements for new ships as prescribed in point (a) of paragraph 2; alterations made to an existing ship which are intended solely to achieve a higher survivability standard shall not be regarded as modifications of a major character;

(f)

the provisions of point (a), unless earlier dates are specified in the 1974 SOLAS Convention, as amended, and the provisions of points (b) and (c), unless earlier dates are specified in Annex I to this Directive, shall not be applied in relation to a ship the keel of which was laid or which was at a similar stage of construction:

(a)

high-speed passenger craft constructed or subjected to repairs, alterations or modifications of a major character on or after 1 January 1996 shall comply with the requirements of Regulation X/3 of the 1974 SOLAS Convention, as amended, unless:

(b)

high-speed passenger craft constructed before 1 January 1996 and complying with the requirements of the High-Speed Craft Code shall continue operation certified under that Code;

high-speed passenger craft constructed before 1 January 1996 and not complying with the requirements of the High-Speed Craft Code may not be engaged on domestic voyages unless they were already in operation on domestic voyages in a Member State on 4 June 1998, in which case they may be allowed to continue their domestic operation in that Member State; such craft shall comply with the requirements of the DSC Code;

(c)

the construction and maintenance of high-speed passenger craft and their equipment shall comply with the rules for the classification of high-speed craft of a recognised organisation, or equivalent rules used by an Administration in accordance with Article 14(2) of Directive 94/57/EC.

(a)

the Member State shall inform the Commission and the other Member States of its decision without delay, giving substantiated reasons therefor;

(b)

the Commission shall examine whether the suspension or the additional measures are justified for reasons of serious danger to safety and to the environment;

(c)

it shall be decided, in accordance with the procedure referred to in Article 11(2), whether or not the decision of the Member State to suspend the operation of such ship or craft or to impose the additional measures is justified for reasons of serious danger to safety of life or property, or to the environment, and, if the suspension or the measures are not justified, that the Member State concerned shall be required to withdraw the suspension or the measures.

(a)

the definitions in points (a), (b), (c), (d) and (v) of Article 2;

(b)

the provisions relating to procedures and guidelines for surveys referred to in Article 12;

(c)

the provisions concerning the 1974 SOLAS Convention, as amended, and the High-Speed Craft Code, including its subsequent amendments, laid down in Articles 4(3), 6(4), 12(3) and 13(3);

(d)

the specific references to the ‘International Conventions’ and IMO resolutions referred to in points (g), (m) and (q) of Article 2, point (a) of Article 3(2), points (b) and (c) of Article 6(1), point (b) of Article 6(2) and Article 13(3).

(a)

apply, for the purpose of this Directive, amendments made to the International Conventions;

(b)

improve the technical specifications thereof, in the light of experience.

(a)

a survey before the ship is put into service;

(b)

a periodical survey once every 12 months; and

(c)

additional surveys, as the occasion arises.

(a)

an initial survey, before the ship is put into service on domestic voyages in a host State, for existing ships engaged on domestic voyages in the Member State the flag of which they are entitled to fly;

(b)

a periodical survey once every 12 months; and

(c)

additional surveys, as the occasion arises.

(a)

to expedite the ongoing work within the IMO to revise the regulations of Chapters II-1, II-2 and III of the 1974 SOLAS Convention, as amended, containing issues left to the discretion of the Administration, to establish harmonised interpretations for those regulations and to adopt amendments to the latter accordingly; and

(b)

to adopt measures for mandatory application of the principles underlying the provisions of MSC Circular 606 on Port State Concurrence with SOLAS Exemptions.

1.

2.

1.

2.

3.

4.

5.

6.

7.

8.

8-1.

8-2.

8-3.

9.

10.

11.

12.

13.

14.

15.

16.

17.

17-1.

17-2.

17-3.

18.

19.

20.

21.

22.

23.

24.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

1.

2.

3.

4.

5.

1.

2.

3.

4.

5.

6.

7.

8.

9.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

1.

2.

3.

4.

5.

6.

6-1.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

1.

2.

3.

4.

5.

5-1.

5-2.

5-3.

6.

7.

8.

8a.

9.

10.

11.

12.

13.

—

any change that substantially alters the dimensions of a ship,

example: lengthening by adding new midbody,

—

any change that substantially alters the passenger-carrying capacity of a ship,

example: vehicle deck converted to passenger accommodation,

—

any change that substantially increases a ship’s service life,

example: renewal of passenger accommodation on one entire deck.

.1

.2

Length of the ship is the length measured between perpendiculars taken at the extremities of the deepest subdivision load line.

.3

Breadth of the ship is the extreme width from outside of frame to outside of frame at or below the deepest subdivision load line.

.4

Draught is the vertical distance from the moulded base line amidships to the subdivision load line in question.

.5

Deadweight is the difference in tonnes between the displacement of a ship in water of a specific gravity of 1,025 at the load waterline corresponding to the assigned summer freeboard and the lightweight of the ship.

.6

Lightweight is the displacement of a ship in tonnes without cargo, fuel, lubricating oil, ballast water, fresh water and feedwater in tanks, consumable stores, and passengers and crew and their effects.

.7

Bulkhead deck is the uppermost deck up to which the transverse watertight bulkheads are carried.

.8

Margin line is a line drawn at least 76 mm below the upper surface of the bulkhead deck at side.

.9

Permeability of a space is the percentage of that space which can be occupied by water. The volume of a space which extends above the margin line shall be measured only to the height of that line.

.10

Machinery space is to be taken as extending from the moulded base line to the margin line and between the extreme main transverse watertight bulkheads, bounding the spaces containing the main and auxiliary propulsion machinery, and boilers serving the needs of propulsion.

.11

Passenger spaces are those spaces which are provided for the accommodation and use of passengers, excluding baggage, store, provision and mail rooms.

.12

Watertight in relation to structure means capable of preventing the passage of water through the structure in any direction under the head of water likely to occur in the intact or damage condition.

.13

Weathertight means that water will not penetrate into the ship in any sea conditions.

.14

Ro-ro passenger ship means a passenger ship with ro-ro cargo spaces or special category spaces as defined in Regulation II-2/A/2.

.1

.2

Steering gear power unit is:

.3

Auxiliary steering gear is the equipment other than any part of the main steering gear necessary to steer the ship in the event of failure of the main steering gear but not including the tiller, quadrant or components serving the same purpose.

.4

Normal operational and habitable condition is a condition under which the ship as a whole, the machinery, services, means and aids ensuring propulsion, ability to steer, safe navigation, fire and flooding safety, internal and external communications and signals, means of escape, and emergency boat winches, as well as the designed comfortable conditions of habitability are in working order and functioning normally.

.5

Emergency condition is a condition under which any services needed for normal operational and habitable conditions are not in working order due to failure of the main source of electrical power.

.6

Main source of electrical power is a source intended to supply electrical power to the main switchboard for distribution to all services necessary for maintaining the ship in normal operational and habitable condition.

.7

Dead ship condition is the condition under which the main propulsion plant, boilers and auxiliaries are not in operation due to the absence of power.

.8

Main generating station is the space in which the main source of electrical power is situated.

.9

Main switchboard is a switchboard which is directly supplied by the main source of electrical power and is intended to distribute electrical energy to the ship’s services.

.10

Emergency switchboard is a switchboard which in the event of failure of the main electrical power supply system is directly supplied by the emergency source of electrical power or the transitional source of emergency power and is intended to distribute electrical energy to the emergency services.

.11

Emergency source of electrical power is a source of electrical power, intended to supply the emergency switchboard in the event of failure of the supply from the main source of electrical power.

.12

Maximum ahead service speed is the greatest speed which the ship is designed to maintain in service at sea at the deepest seagoing draught.

.13

Maximum astern speed is the speed which it is estimated the ship can attain at the designed maximum astern power at the deepest seagoing draught.

.14(a)

Machinery spaces are all machinery spaces of category A and all other spaces containing propelling machinery, boilers, oil fuel units, steam and internal combustion engines, generators and major electrical machinery, oil filling stations, refrigerating, stabilising, ventilation and air conditioning machinery, and similar spaces, and trunks to such spaces.

.14(b)

Machinery spaces of category A are those spaces and trunks to such spaces which contain:

.15

Power actuating system is the hydraulic equipment provided for supplying power to turn the rudderstock, comprising a steering gear power unit or units, together with the associated pipes and fittings, and a rudder actuator. The power actuating systems may share common mechanical components, i.e. tiller, quadrant and rudder stock, or components serving the same purpose.

.16

Control stations are those spaces in which the ship’s radio or main navigating equipment or the emergency source of power is located or where the fire recording or fire control equipment is centralised.

(a)

The area under the curve of righting lever (GZ curve) shall not be less than:

(b)

The righting lever GZ shall be at least 0,20 metres at an angle of heel equal to or greater than 30 °.

(c)

The maximum righting lever GZ shall occur at an angle of heel preferably exceeding 30 ° but not less than 25 °.

(d)

The initial transverse metacentric height shall not be less than 0,15 metres.

.1

The floodable length at a given point is the maximum portion of the length of the ship, having its centre at the point in question, which can be flooded, under the assumption for permeability given below, without the ship being submerged beyond the margin line.

.2

In the case of a ship not having a continuous bulkhead deck, the floodable length at any point may be determined to an assumed continuous margin line which at no point is less than 76 mm below the top of the deck at side to which the bulkheads concerned and the shell are carried watertight.

.3

Where a portion of an assumed margin line is appreciably below the deck to which bulkheads are carried, the Administration of the flag State may permit a limited relaxation in the watertightness of those portions of the bulkheads which are above the margin line and immediately under the higher deck.

.1

Where in a portion or portions of a ship the watertight bulkheads are carried to a higher deck than in the remainder of the ship and it is desired to take advantage of this higher extension of the bulkheads in calculating the floodable length, separate margin lines may be used for each such portion of the ship provided that:

.2

A compartment may exceed the permissible length determined by the rules of Regulation 4 provided the combined length of each pair of adjacent compartments to which the compartment in question is common does not exceed either the floodable length or twice the permissible length, whichever is less.

.3

A main transverse bulkhead may be recessed provided that all parts of the recess lie inboard of vertical surfaces on both sides of the ship, situated at a distance from the shell plating equal to one fifth of the breadth of the ship, and measured at right angles to the centreline at the level of the deepest subdivision load line. Any part of a recess which lies outside these limits shall be dealt with as a step in accordance with paragraph .6.

.4

Where a main transverse bulkhead is recessed or stepped, an equivalent plane bulkhead shall be used in determining the subdivision.

.5

Where a main transverse watertight compartment contains local subdivision and the Administration of the flag State is satisfied that, after any assumed side damage extending over a length of 3,0 metres plus 3 % of the length of the ship or 11,0 metres, or 10 % of the length of the ship whichever is the less, the whole volume of the main compartment will not be flooded, a proportionate allowance may be made in the permissible length otherwise required for such compartment. In such a case the volume of the effective buoyancy assumed on the undamaged side shall not be greater than that assumed on the damaged side.

Allowance under this paragraph will only be made if such allowance is not likely to prevent compliance with Regulation 8.

.6

A main transverse bulkhead may be stepped provided that it meets one of the following conditions:

.7

In ships of 100 metres in length and upwards, one of the main transverse bulkheads abaft the forepeak shall be fitted at a distance from the forward perpendicular which is not greater than the permissible length.

.8

If the distance between two adjacent main transverse bulkheads, or their equivalent plank bulkheads, or the distance between the transverse planes passing through the nearest stepped portions of the bulkheads, is less than 3,0 metres plus 3 % of the length of the ship, or 11,0 metres, or 10 % of the length of the ship, whichever is less, only one of these bulkheads shall be regarded as forming part of the subdivision of the ship.

.9

Where the required subdivision factor is 0,50, the combined length of any two adjacent compartments shall not exceed the floodable length.

.1.1

Sufficient intact stability shall be provided in all service conditions so as to enable the ship to withstand the final stage of flooding of any one main compartment which is required to be within the floodable length.

.1.2

Where two adjacent main compartments are separated by a bulkhead which is stepped under the conditions of Regulation 7.6.1, the intact stability shall be adequate to withstand the flooding of those two adjacent compartments.

.1.3

Where the required factor of subdivision is 0,50, the intact stability shall be adequate to withstand the flooding of any two adjacent compartments.

.2.1

The requirements of subparagraph .1 shall be determined by calculations which are in accordance with paragraphs .3, .4 and .6 and which take into consideration the proportions and design characteristics of the ship and the arrangement and configuration of the damaged compartments. In making these calculations the ship is to be assumed in the worst anticipated service condition as regards stability.

.2.2

Where it is proposed to fit decks, inner skins or longitudinal bulkheads of sufficient tightness to seriously restrict the flow of water, proper consideration is to be given to such restrictions in the calculations.

.2.3

The stability required in the final condition after damage, and after equalisation where provided, shall be determined as follows:

.2.4

When major progressive flooding occurs, that is, when it causes a rapid reduction in the righting lever of 0,04 metres or more, the righting lever curve is to be considered as terminated at the angle the progressive flooding occurs and the range and the area referred to in .2.3.1 and .2.3.2 should be measured to that angle.

.2.5

In cases where the progressive flooding is of limited nature that does not continue unabated and causes an acceptably slow reduction in righting lever of less than 0,04 metres, the remainder of the curve shall be partially truncated by assuming that the progressively flooded space is so flooded from the beginning.

.2.6

In intermediate stages of flooding, the maximum righting lever shall be at least 0,05 metres and the range of positive righting levers shall be at least 7. In all cases, only one breach in the hull and only one free surface need be assumed.

.3

For the purpose of making damaged stability calculations the volume and surface permeabilities shall be as follows:

Higher surface permeabilities are to be assumed in respect of spaces which, in the vicinity of the damaged waterplane, contain no substantial quantity of accommodation or machinery and spaces which are not generally occupied by any substantial quantity of cargo or stores.

.4

Assumed extent of damage shall be as follows:

.5

Unsymmetrical flooding is to be kept to a minimum consistent with efficient arrangements. Where it is necessary to correct large angles of heel, the means adopted shall, where practicable, be self-acting, but in any case where controls to cross-flooding fittings are provided they shall be operable from above the bulkhead deck. For new class B, C and D ships the maximum angle of heel after flooding but before equalisation shall not exceed 15 °. Where cross-flooding fittings are required the time for equalisation shall not exceed 15 minutes. Suitable information concerning the use of cross-flooding fittings shall be supplied to the master of the ship.

.6

The final conditions of the ship after damage and, in the case of unsymmetrical flooding, after equalisation measures have been taken shall be as follows:

.7

The master of the ship shall be supplied with the data necessary to maintain sufficient intact stability under service conditions to enable the ship to withstand the critical damage. In the case of ships requiring cross-flooding, the master of the ship shall be informed of the conditions of stability on which the calculations of heel are based and shall be warned that excessive heeling might result should the ship sustain damage when in a less favourable condition.

.8

The data referred to in paragraph .7 to enable the master to maintain sufficient intact stability shall include information which indicates the maximum permissible height of the ship’s centre of gravity above keel (KG), or alternatively the minimum permissible metacentric height (GM), for a range of draughts or displacements sufficient to include all service conditions. The information shall show the influence of various trims taking into account the operational limits.

.9

Each ship shall have scales of draughts marked clearly at the bow and stern. In the case where the draught marks are not located where they are easily readable, or operational constraints for a particular trade make it difficult to read the draught marks, then the ship shall also be fitted with a reliable draught indicating system by which the bow and stern draughts can be determined.

.10

On completion of loading of the ship and prior to its departure, the master shall determine the ship’s trim and stability and also ascertain and record that the ship is in compliance with stability criteria in the relevant regulations. The determination of the ship’s stability shall always be made by calculation. An electronic loading and stability computer or equivalent means may be used for this purpose.

.11

No relaxation from the requirements for damage stability may be considered by the Administration of the flag State unless it is shown that the intact metacentric height in any service condition necessary to meet these requirements is excessive for the service intended.

.12

Relaxations from the requirements for damage stability shall be permitted only in exceptional cases and subject to the condition that the Administration of the flag State is to be satisfied that the proportions, arrangements and other characteristics of the ship are the most favourable to stability after damage which can practically and reasonably be adopted in the particular circumstances.

.1

Existing class B ro-ro passenger ships shall comply with Regulation 8 not later than the date of the first periodical survey after the date of compliance prescribed below, according to the value of A/Amax as defined in the Annex of the Calculation Procedure to Assess the Survivability Characteristics of Existing Ro-Ro Passenger Ships when Using a Simplified Method Based Upon Resolution A.265 (VIII), developed by the Maritime Safety Committee at its 59th session in June 1991 (MSC/Circ. 574):

.1

new ro-ro passenger ships certified to carry 400 persons or more shall comply with the provisions of paragraph .2.3 of Regulation II-1/B/8, assuming the damage applied anywhere within the ship’s length L; and

.2

existing ro-ro passenger ships certified to carry 400 persons or more shall comply with the requirements of paragraph .1 not later than the date of the first periodical survey after the date of compliance prescribed in subparagraph .2.1, .2.2 or .2.3 which occurs the latest:

.1

A forepeak or collision bulkhead shall be fitted which shall be watertight up to the bulkhead deck. This bulkhead shall be located at a distance from the forward perpendicular of not less than 5 % of the length of the ship and not more than 3 metres plus 5 % of the length of the ship.

.2

Where any part of the ship below the waterline extends forward of the forward perpendicular, e. g. a bulbous bow, the distances stipulated in paragraph .1 shall be measured from a point either:

whichever gives the smallest measurement.

.3

Where a long forward superstructure is fitted, the forepeak or collision bulkhead shall be extended weathertight to the next full deck above the bulkhead deck. The extension shall be so arranged as to preclude the possibility of the bow door causing damage to it in the case of damage to, or detachment of, a bow door.

.4

The extension required in paragraph .3 need not be fitted directly above the bulkhead below provided all parts of the extension are not located forward of the forward limit specified in paragraph .1 or in paragraph .2.

However, in existing class B ships:

.5

Ramps not meeting the above requirements shall be disregarded as an extension to the collision bulkhead.

.6

In existing class B ships, the requirements of paragraph .3 and .4 apply as from the date of the first periodical survey after 1 July 1998.

.7

An afterpeak bulkhead, and bulkheads dividing the machinery space, from the cargo and passenger spaces forward and aft, shall also be fitted and made watertight up to the bulkhead deck. The afterpeak bulkhead may, however, be stepped below the bulkhead deck, provided the degree of safety of the ship as regards subdivision is not thereby diminished.

.8

In all cases stern tubes shall be enclosed in watertight spaces. The stern gland shall be situated in a watertight shaft tunnel or other watertight space separate from the stern tube compartment and of such volume that, if flooded by leakage through the stern gland, the margin line will not be submerged.

.1

In new class B, C and D and existing class B ships, and new ships constructed on or after 1 January 2003 with a length of 24 metres and above, a double bottom shall be fitted extending from the forepeak bulkhead to the afterpeak bulkhead as far as this is practicable and compatible with the design and proper working of the ship.

.2

Where a double bottom is required to be fitted its depth shall comply with the standards of a recognised organisation and the inner bottom shall be continued out to the ship’s sides in such a manner as to protect the bottom to the turn of the bilge. Such protection will be deemed satisfactory if the line of intersection of the outer edge of the margin plate with the bilge plating is not lower at any part than a horizontal plane passing through the point of intersection with the frame line amidships of a transverse diagonal line inclined at 25 ° to the base line and cutting it at a point one half of the ship’s moulded breadth from the middle line.

.3

Small wells constructed in the double bottom in connection with drainage arrangements of holds, etc., shall not extend downwards more than necessary. The depth of the well shall in no case be more than the depth less 460 mm of the double bottom at the centreline, nor shall the well extend below the horizontal plane referred to in paragraph .2. A well extending to the outer bottom is, however, permitted at the after end of the shaft tunnel. Other wells (e.g. for lubricating oil under main engines) may be permitted by the Administration of the flag State if satisfied that the arrangements give protection equivalent to that afforded by a double bottom complying with this regulation.

.4

A double bottom need not be fitted in way of watertight compartments of moderate size used exclusively for the carriage of liquids, provided the safety of the ship, in the event of bottom or side damage, is not, in the opinion of the Administration of the flag State, thereby impaired.

.5

Notwithstanding paragraph .1 of this Regulation 10, the Administration of the flag State may permit a double bottom to be dispensed with in any part of the ship which is subdivided by a factor not exceeding 0,5, if satisfied that the fitting of a double bottom in that part would not be compatible with the design and proper working of the ship.

.1

In order that the required degree of subdivision shall be maintained, a load line corresponding to the approved subdivision draught shall be assigned and marked on the ship’s sides amidships. A ship having spaces which are specially adapted for the accommodation of passengers and the carriage of cargo alternatively may, if owners desire, have one or more additional load lines assigned and marked to correspond with the subdivision draughts which the Administration of the flag State may approve for alternative service conditions.

.2

The subdivision load lines assigned and marked shall be recorded in the Passenger Ship Safety Certificate, and shall be identified by the notation C.1 if there is only one subdivision load line.

If there is more than one subdivision load line, the alternative conditions shall be identified by the notations C.2, C.3, C.4 etc. (2).

.3

The freeboard corresponding to each of these load lines shall be measured at the same position and from the same deck line as the freeboards determined in accordance with the International Convention on Load Lines in force.

.4

The freeboard corresponding to each approved subdivision load line and the conditions of service for which it is approved shall be clearly indicated on the Passenger Ship Safety Certificate.

.5

In no case shall any subdivision load line mark be placed above the deepest load line in salt water as determined by the strength of the ship or the International Convention on Load Lines in force.

.6

Whatever may be the position of the subdivision load line marks, a ship shall in no case be loaded so as to submerge the load line mark appropriate to the season and locality as determined in accordance with the International Convention on Load Lines in force.

.7

A ship shall in no case be so loaded that the subdivision load line mark appropriate to the particular voyage and condition of service is submerged.

.1

Each watertight subdivision bulkhead, whether transverse or longitudinal, shall be constructed in such a manner that it shall be capable of supporting, with a proper margin of resistance, the pressure due to the maximum head of water which it might have to sustain in the event of damage to the ship but at least the pressure due to a head of water up to the margin line. The construction of these bulkheads shall be in accordance with the standards of a recognised organisation.

.2.1

Steps and recesses in bulkheads shall be watertight and as strong as the bulkhead at the place where each occurs.

.2.2

Where frames or beams pass through a watertight deck or bulkhead, such deck or bulkhead shall be made structurally watertight without the use of wood or cement.

.3

Testing main compartments by filling them with water is not compulsory. When testing by filling with water is not carried out, a hose test shall be carried out where practicable. This test shall be carried out in the most advanced stage of the fitting-out of the ship. Where a hose test is not practicable because of possible damage to machinery, electrical equipment insulation or out fitting items, it may be replaced by a careful visual examination of welded connections, supported where deemed necessary by means such as a dye penetrant test or ultrasonic leak test or an equivalent test. In any case, a thorough inspection of the watertight bulkheads shall be carried out.

.4

The forepeak, double bottoms (including duct keels) and inner skins shall be tested with water to a head corresponding to the requirements of paragraph .1 of this Regulation 12.

.5

Tanks which are intended to hold liquids, and which form part of the subdivision of the ship, shall be tested for tightness with water to a head up to the deepest subdivision load line or to a head corresponding to two thirds of the depth from the top of keel to the margin line in way of the tanks, whichever is the greater, provided that in no case shall the test head be less than 0,9 metres above the top of the tank; if testing by water is impracticable, air leak testing while the tanks are subjected to an air pressure of not more than 0,14 bar may be accepted.

.6

The tests referred to in paragraphs .4 and .5 are for the purpose of ensuring that the subdivision structural arrangements are watertight and are not to be regarded as a test of the fitness of any compartment for the storage of oil fuel or for other special purposes for which a test of a superior character may be required depending on the height to which the liquid has access in the tank or its connections.

.1

in the collision bulkhead below the margin line;

.2

in watertight transverse bulkheads dividing a cargo space from an adjoining cargo space, except as provided for in paragraph .10.1 of this Regulation 13 and in Regulation 14.

—

hand-operated only; or

—

power-operated as well as hand-operated.

.1

shall have a vertical or horizontal motion;

.2

shall, subject to paragraph .11, be normally limited to a maximum clear width of 1,2 metres. The Administration of the flag State may permit larger doors only to the extent considered necessary for the effective operation of the ship provided that other safety measures, including the following, are taken into consideration:

.3

shall be fitted with the necessary equipment to open and close the door using electric power, hydraulic power, or any other form of power that is acceptable to the Administration of the flag State;

.4

shall be provided with an individual hand-operated mechanism. It shall be possible to open and close the door by hand at the door itself from either side, and in addition, close the door from an accessible position above the bulkhead deck with an all-round crank motion or some other movement providing the same degree of safety acceptable to the Administration of the flag State. Direction of rotation or other movement is to be clearly indicated on all operating positions. The time necessary for the complete closure of the door, when operated by hand gear, shall not exceed 90 seconds with the ship in upright position;

.5

shall be provided with controls for opening and closing the door by power from both sides of the door and also for closing the door by power from the central operating console at the navigating bridge;

.6

shall be provided with an audible alarm, distinct from any other alarm in the area, which will sound whenever the door is closed remotely by power and which shall sound for at least 5 seconds but no more than 10 seconds before the door begins to move and shall continue sounding until the door is completely closed. In the case of remote hand operation it is sufficient for the audible alarm to sound only when the door is moving. Additionally, in passenger areas and areas of high ambient noise, the Administration of the flag State may require the audible alarm to be supplemented by an intermittent visual signal at the door; and

.7

shall have an approximately uniform rate of closure under power. The closure time, from the time the door begins to move to the time it reaches the completely closed position, shall in no case be less than 20 seconds and no more than 40 seconds with the ship in upright position.

.1

a centralised hydraulic system with two independent power sources each consisting of a motor and pump capable of simultaneously closing all doors. In addition, there shall be for the whole installation hydraulic accumulators of sufficient capacity to operate all the doors at least three times, i. e. closed-open-closed, against an adverse list of 15 °. This operating cycle shall be capable of being carried out when the accumulator is at the pump cut-in pressure. The fluid used shall be chosen considering the temperature liable to be encountered by the installation during its service. The power-operating system shall be designed to minimise the possibility of having a single failure in the hydraulic piping adversely affect the operation of more than one door. The hydraulic system shall be provided with a low-level alarm for hydraulic fluid reservoirs serving the power-operated system and a low gas pressure alarm or other effective means of monitoring loss of stored energy in hydraulic accumulators. These alarms are to be audible and visual and shall be situated on the central operating console at the navigating bridge; or

.2

an independent hydraulic system for each door with each power source consisting of a motor and pump capable of opening and closing the door. In addition, there shall be a hydraulic accumulator of sufficient capacity to operate the door at least three times, i. e. closed-open-closed, against an adverse list of 15 °. This operating cycle shall be capable of being carried out when the accumulators at the pump cut-in pressure. The fluid used shall be chosen considering the temperatures liable to be encountered by the installation during its service. A low gas pressure group alarm or other effective means of monitoring loss of stored energy in hydraulic accumulators shall be provided at the central operating console on the navigating bridge. Loss of stored energy indication at each local operating position shall also be provided; or

.3

an independent electrical system and motor for each door with each power source consisting of a motor capable of opening and closing the door. The power source shall be capable of being automatically supplied by the transitional source of emergency electrical power in the event of failure of either the main or emergency source of electrical power and with sufficient capacity to operate the door at least three times, i. e. closed-open-closed, against an adverse list of 15 °.

.1

This regulation applies to passenger ships designed or adapted for the carriage of goods vehicles and accompanying personnel.

.2

If in such a ship the total number of passengers, including persons accompanying vehicles, does not exceed N = 12 + A/25, where A = total deck area (square metres) of spaces available for the stowage of goods vehicles and where the clear height at the stowage position and at the entrance to such spaces is not less than 4 metres, the provisions of Regulation 13, paragraph .10, in respect of watertight doors apply except that the doors may be fitted at any level in watertight bulkheads dividing cargo spaces. Additionally, indicators are required on the navigating bridge to show automatically when each door is closed and all door fastenings are secured.

.3

When applying the provisions of this chapter to such a ship, N shall be taken as the maximum number of passengers for which the ship may be certified in accordance with this regulation.

.1

The handwheels or handles of the sea cocks shall be easily accessible for operation. All valves which are used as seacocks shall close by clockwise movement of their handwheels.

.2

Discharge taps or valves on the side of the ship for blow-off water from boilers shall be located in easily accessible locations and not beneath deck plating. Taps or valves shall be so designed that it is easy to see whether they are open or closed. Taps shall be provided with safety screens, so designed that the key cannot be lifted off when the tap is open.

.3

All valves and taps in pipe systems such as bilge and ballast systems, fuel oil and lubricating oil systems, fire extinguishing and sluicing systems, cooling water and sanitary systems, etc. shall be clearly marked as to their functions.

.4

Other outlet pipes shall, if they emerge below the deepest subdivision load line, be provided with equivalent means of shut-off on the side of the ship; if they emerge above the deepest subdivision load line, they shall be provided with an ordinary storm valve. In both cases the valves may be omitted if pipes are used of the same thickness as the plating indirect outlets from toilets and wash-basins, and floor outlets from washrooms etc. provided with deadlights or otherwise protected against water shock. The wall thickness of such pipes need not, however, be greater than 14 mm.

.5

If a valve with a direct closing mechanism is fitted, the place from which it may be operated shall always be easily accessible, and there shall be a means of indicating whether the valve is open or closed.

.6

When valves with direct closing mechanisms are placed in machinery spaces, it is sufficient that they be operable from where they are located, provided that this place is easily accessible under all conditions.

.1

All reasonable and practicable measures shall be taken to limit the entry and spread of water above the bulkhead deck. Such measures may include partial bulkheads or webs. When partial watertight bulkheads and webs are fitted on the bulkhead deck, above or in the immediate vicinity of main subdivision bulkheads, they shall have watertight shell and bulkhead deck connections so as to restrict the flow of water along the deck when the ship is in a heeled damaged condition. Where the partial watertight bulkhead does not line up with the bulkhead below, the bulkhead deck between shall be made effectively watertight.

.2

The bulkhead deck or a deck above it shall be weathertight. All openings in the exposed weather deck shall have coamings of ample height and strength and shall be provided with efficient means for expeditiously closing them weathertight. Freeing ports, open rails and scuppers shall be fitted as necessary for rapidly clearing the weather deck of water under all weather conditions.

.3

In existing class B ships, the open end of air pipes terminating within a superstructure shall be at least 1 metre above the waterline when the ship heels to an angle of 15, or the maximum angle of heel during intermediate stages of flooding, as determined by direct calculation, whichever is the greater. Alternatively, air pipes from tanks other than oil tanks may discharge through the side of the superstructure. The provisions of this paragraph are without prejudice to the provisions of the International Convention on Load Lines in force.

.4

Sidescuttles, gangway, cargo ports and the other means for closing openings in the shell plating above the margin line shall be of efficient design and construction and of sufficient strength having regard to the spaces in which they are fitted and their positions relative to the deepest subdivision load line.

.5

Efficient inside deadlights, so arranged that they can be easily and effectively closed and secured watertight, shall be provided for all sidescuttles to spaces below the first deck above the bulkhead deck.

.1

The following doors, located above the margin line, shall be closed and locked before the ship proceeds on any voyage, and shall remain closed and locked until the ship is at its next berth:

.2

Notwithstanding the requirements of paragraphs .1.1 and .1.4, the Administration of the flag State may authorise that particular doors can be opened at the discretion of the master, if necessary for the operation of the ship or the embarking and disembarking of passengers, when the ship is at safe anchorage and provided that the safety of the ship is not impaired.

.3

The master shall ensure that an effective system of supervision and reporting of the closing and opening of the doors referred to in paragraph .1 is implemented.

.4

The master shall ensure, before the ship proceeds on any voyage, that an entry in the logbook, as required in Regulation 22, is made of the time of the last closing of the doors specified in paragraph .1 and the time of any opening of particular doors in accordance with paragraph .2.

.1.1

Subject to the provisions of paragraphs .1.2 and .1.3, all accesses that lead to spaces below the bulkhead deck shall have a lowest point which is not less than 2,5 metres above the bulkhead deck;

.1.2

where vehicle ramps are installed to give access to spaces below the bulkhead deck, their openings shall be able to be closed weathertight to prevent ingress of water below, alarmed and indicated to the navigation bridge;

.1.3

the Administration of the flag State may permit the fitting of particular accesses to spaces below the bulkhead deck provided they are necessary for the essential working of the ship, e.g. movement of machinery and stores, subject to such accesses being made watertight, alarmed and indicated to the navigation bridge;

.1.4

the accesses referred to in paragraphs .1.2 and .1.3 shall be closed before the ship leaves the berth on any voyage and shall remain closed until the ship is at its next berth;

.1.5

the master shall ensure that an effective system of supervision and reporting of the closing and opening of such accesses referred to in paragraphs .1.2 and .1.3 is implemented; and

.1.6

the master shall ensure, before the ship leaves the berth on any voyage, that an entry in the logbook, as required by Regulation II-1/B/22, is made of the time of the last closing of the accesses referred to in paragraphs .1.2 and .1.3;

.1.7

new class C ro-ro passenger ships of less than 40 metres in length and new class D ro-ro passenger ships may, instead of complying with paragraphs .1.1 to .1.6, comply with paragraphs .2.1 to .2.4, provided that coaming and sill heights are at least 600 mm on open ro-ro cargo decks and at least 380 mm on enclosed ro-ro cargo decks.

.2.1

All accesses from the ro-ro deck that lead to spaces below the bulkhead deck shall be made weathertight and means shall be provided on the navigation bridge, indicating whether the access is open or closed;

.2.2

all such accesses shall be closed before the ship leaves the berth on any voyage and shall remain closed until the ship is at its next berth;

.2.3

notwithstanding the requirements of paragraph .2.2, the Administration of the flag State may permit some accesses to be opened during the voyage but only for a period sufficient to permit through passage and, if required, for the essential working of the ship; and

.2.4

the requirements of paragraph .2.1 apply as from the date of the first periodical survey after 1 July 1998.

.1

All transverse and longitudinal bulkheads which are taken into account as effective to confine the seawater accumulated on the ro-ro deck shall be in place and secured before the ship leaves the berth and remain in place and secured until the ship is at its next berth.

.2

Notwithstanding the requirements of paragraph .1, the Administration of the flag State may permit some accesses within such bulkheads to be opened during the voyage but only for sufficient time to permit through passage and, if required, for the essential working of the ship.

.1

Every passenger ship shall be inclined upon its completion and the elements of its stability determined. The master shall be supplied with such information, approved by the Administration of the flag State, as is necessary to enable him by rapid and simple processes to obtain accurate guidance as to the stability of the ship under varying conditions of service.

.2

Where any alterations are made to a ship so as to affect materially the stability information supplied to the master, amended stability information shall be provided. If necessary the ship shall be re-inclined.

.3

At periodical intervals not exceeding five years, a lightweight survey shall be carried out to verify any changes in the light ship displacement and longitudinal centre of gravity. The ship shall be re-inclined whenever, in comparison with the approved stability information, a deviation from the lightship displacement exceeding 2 % or a deviation of the longitudinal centre of gravity exceeding 1 % of the length of the ship is found or anticipated.

.4

The Administration of the flag State may allow the inclining test of an individual ship to be dispensed with provided basic stability data are available from the inclining test of a sister ship and it is shown to the satisfaction of the Administration of the flag State that reliable stability information for the exempted ship can be obtained from such basic data.

.1

Indicators shall be provided on the navigating bridge for all shell doors, loading doors and other closing appliances which, if left open or not properly secured, could lead to flooding of a special category space or ro-ro cargo space. The indicator system shall be designed on the fail-safe principle and shall show by visual alarms if the door is not fully closed or if any of the securing arrangements are not in place and fully locked and by audible alarms if such door or closing appliances become open or the securing arrangements become unsecured. The indicator panel on the navigating bridge shall be equipped with a mode selection function ‘harbour/sea voyage’ so arranged that an audible alarm is given on the navigation bridge if the ship leaves harbour with the bow doors, inner doors, stern ramp or any other shell doors not closed or any closing device not in correct position. The power supply for the indicator system shall be independent of the power supply for operating and securing the doors. Indicator systems, approved by the Administration of the flag State, which were installed on board existing ships, need not be changed.

.2

Television surveillance and a water leakage detection system shall be arranged to provide an indication to the navigation bridge and to the engine control station of any leakage through inner and outer bow doors, stern doors or any other shell doors which could lead to flooding of special category spaces or ro-ro cargo spaces.

.3

Special category spaces and ro-ro cargo spaces shall be continuously patrolled or monitored by effective means, such as television surveillance, so that any movement of vehicles in adverse weather conditions and unauthorised access by passengers thereto can be detected whilst the ship is under way.

.4

Documented operating procedures for closing and securing all shell doors, loading doors and other closing appliances which, if left open or not properly secured, could lead to flooding of a special category space or ro-ro cargo space, shall be kept on board and posted at an appropriate place.

.1

Drills for the operating of the watertight doors, sidescuttles, valves and closing mechanisms of scuppers shall take place weekly.

.2

All watertight doors in main transverse bulkheads, in use at sea, shall be operated daily.

.3

The watertight doors and all mechanisms and indicators connected therewith, all valves, the closing of which is necessary to make a compartment watertight, and all valves the operation of which is necessary for damage control cross-connections shall be periodically inspected at sea at least once a week.

.4

Such valves, doors and mechanisms shall be suitably marked to ensure that they may be properly used to provide maximum safety.

.1

Hinged doors, portable plates, sidescuttles, gangway and cargo ports and other openings, which are required by these regulations to be kept closed during navigation, shall be closed before the ship leaves the port. The time of closing and the time of opening (if permissible under these Regulations) shall be recorded in the logbook.

.2

A record of all drills and inspections required by Regulation 21 shall be entered in the logbook with an explicit record of any defects which may be disclosed.

.1

On external decks to which passengers are permitted access, and where there is no bulwark of adequate height provided, railings shall be provided of a height of minimum 1 100 mm above the deck and of such design and construction as to prevent any passenger from climbing on these railings and from accidentally falling from that deck.

.2

Stairs and landings on such external decks shall be provided with railings of equivalent construction.

.1

The machinery, boilers and other pressure vessels, associated piping systems and fittings shall be so installed and protected as to reduce to a minimum any danger to persons on board, due regard being paid to moving parts, hot surfaces and other hazards.

.2

Means shall be provided whereby normal operation of propulsion machinery can be sustained or restored even though one of the essential auxiliaries becomes inoperative.

.3

Means shall be provided to ensure that the machinery can be brought into operation from the dead ship condition without external aid.

.4

Main propulsion machinery and all auxiliary machinery essential to the propulsion and the safety of the ship shall, as fitted in the ship, be designed to operate when the ship is upright and when inclined at any angle of list up to and including 15 ° either way under static conditions and 22,5 ° under dynamic conditions (rolling) either way and simultaneously inclined dynamically (pitching) 7,5 ° by bow or stern.

.5

Means shall be provided for the propulsion machinery and the propeller to be stopped in cases of emergencies from relevant positions outside of the engine room/engine control room, e.g. open deck or the wheel house.

.6

Location and arrangement of vent pipes for fuel oil service, settling and lubricating oil tanks shall be such that in the event of a broken vent pipe this shall not directly lead to the risk of ingress of seawater splashes or rainwater. Two fuel oil service tanks for each type of fuel used on board necessary for propulsion and vital systems or equivalent arrangements shall be provided on each ship, with a capacity of at least 8 hours for class B ships and at least 4 hours for class C and D ships, at maximum continuous rating of the propulsion plant and normal operating load at sea of the generator plant.

.1

Internal combustion engines of a cylinder diameter of 200 mm, or a crankcase volume of 0,6 m3 and above shall be provided with crankcase explosion relief valves of a suitable type with sufficient relief area. The relief valves shall be arranged or provided with means to ensure that discharge from them is so directed as to minimise the possibility of injury to personnel.

.1.1

An efficient bilge pumping system shall be provided, capable of pumping from and draining any watertight compartment other than a space permanently appropriated for the carriage of fresh water, water ballast, oil fuel or liquid cargo and for which other efficient means of pumping are provided, under all practical conditions. Efficient means shall be provided for draining water from insulated holds.

.1.2

Sanitary, ballast and general service pumps may be accepted as independent power bilge pumps if fitted with the necessary connections to the bilge pumping system.

.1.3

All bilge pipes used in or under fuel storage tanks or in boiler or machinery spaces, including spaces in which oil-settling tanks or oil fuel pumping units are situated, shall be of steel or other suitable material.

.1.4

The arrangement of the bilge and ballast pumping system shall be such as to prevent the possibility of water passing from the sea and from water ballast spaces into the cargo and machinery spaces, or from one compartment to another. Provision shall be made to prevent any deep tank having bilge and ballast connections being inadvertently flooded from the sea when containing cargo, or being discharged through a bilge pump when containing water ballast.

.1.5

All distribution boxes and manually operated valves in connection with the bilge pumping arrangements shall be in positions which are accessible under ordinary circumstances.

.1.6

Provision shall be made for the drainage of enclosed cargo spaces situated on the bulkhead deck.

.1.6.1

Where the freeboard to the bulkhead deck is such that the deck edge is immersed when the ship heels more than 5 °, the drainage shall be by means of a sufficient number of scuppers of suitable size discharging directly overboard, fitted in accordance with the requirements of Regulation 15.

.1.6.2

Where the freeboard is such that the edge of the bulkhead deck is immersed when the ship heels 5 ° or less, the drainage of the enclosed cargo spaces on the bulkhead deck shall be led to a suitable space, or spaces, of adequate capacity, having high water level alarm and provided with suitable arrangements for discharge overboard. In addition it will be ensured that:

.1.6.3

The drainage from ro-ro decks and car decks shall be of sufficient capacity that the scuppers, wash ports etc. on the starboard and the port side shall be able to cope with a quantity of water originating from drencher and fire pumps, taking into account the ship’s conditions of heel and trim.

.1.6.4

When provided with sprinkler installations and hydrants, passenger and crew lounges shall have an adequate number of scuppers, sufficient to cope with the quantity of water originating from fire extinguishing by the room’s sprinkler heads and from two fire hoses with jets. The scuppers shall be located in the most effective positions, e.g. in each corner.

.2.1

The bilge pumping system required by paragraph .1.1 shall be capable of operation under all practicable conditions after a casualty whether the ship is upright or listed. For this purpose wing suctions shall generally be fitted except in narrow compartments at the end of the ship where one suction may be sufficient. In compartments of unusual form, additional suctions may be required. Arrangements shall be made whereby water in the compartment may find its way to the suction pipes.

.2.2

Where practicable, the power bilge pumps shall be placed in separate watertight compartments and so arranged or situated that these compartments will not be flooded by the same damage. If the main propulsion machinery, auxiliary machinery and boilers are in two or more watertight compartments, the pumps available for bilge service shall be distributed as far as is possible throughout these compartments.

.2.3

With the exception of additional pumps which may be provided for peak compartments only, each required bilge pump shall be so arranged as to draw water from any space required to be drained by paragraph .1.1.

.2.4

Each power bilge pump shall be capable of pumping water through the required main bilge pipe at a speed of not less than 2 m/sec. Independent power bilge pumps situated in machinery spaces shall have direct suctions from these spaces, except that not more than two such suctions shall be required in any one space. Where two or more such suctions are provided there shall be at least one on each side of the ship. Direct suctions shall be suitably arranged and those in a machinery space shall be of a diameter not less than that required for the bilge main.

.2.5

In addition to the direct bilge suction or suctions required by paragraph .2.4 a direct emergency bilge suction fitted with a non-return valve shall be led from the largest available independent power-driven pump to the drainage level of the machinery space; the suction shall be of the same diameter as the main inlet to the pumps used.

.2.6

The spindles of the sea inlet and direct suction valves shall extend well above the engine-room platform.

.2.7

All bilge suction piping up to the connection to the pumps shall be independent of other piping.

.2.8

The diameter ‘d’ of the main and branch bilge suction pipes shall be calculated according to the following formulae. However, the actual internal diameter may be rounded off to the nearest standard size acceptable to the Administration of the flag State: main bilge suction pipe:

branch bilge suction pipes between collecting boxes and suctions:

where:

.2.9

Provision shall be made to prevent the compartment served by any bilge suction pipe being flooded in the event of the pipe being severed or otherwise damaged by collision or grounding in any other compartment. For this purpose, where the pipe is at any part situated nearer the side of the ship than one fifth of the breadth of the ship (measured at right angles to the centreline at the level of the deepest subdivision load line), or is in a duct keel, a non-return valve shall be fitted to the pipe in the compartment containing the open end.

.2.10

Distribution boxes, cocks and valves in connection with the bilge pumping system shall be so arranged that, in the event of flooding, one of the bilge pumps may be operative on any compartment; in addition, damage to a pump or its pipe connecting to the bilge main outboard of a line drawn at one fifth of the breadth of the ship shall not put the bilge system out of action. If there is only one system of pipes common to all the pumps, the necessary valves for controlling the bilge suctions must be capable of being operated from above the bulkheads deck. Where in addition to the main bilge pumping system an emergency bilge pumping system is provided, it shall be independent of the main system and so arranged that a pump is capable of operating on any compartment under flooding condition as specified in paragraph .2.1; in the case only the valves necessary for the operation of the emergency system need be capable of being operated from above the bulkhead deck.

.2.11

All cocks and valves referred to in paragraph .2.10 which can be operated from above the bulkhead deck shall have their controls at their place of operation clearly marked and shall be provided with means to indicate whether they are open or closed.

up to 250 passengers

:

one main engine pump and one independent power pump, located and powered outside the engine room,

over 250 passengers

:

one main engine pump and two independent power pumps, one of which has to be located and powered outside the engine room.

.1

Sufficient power for going astern shall be provided to secure proper control of the ship in all normal circumstances.

.2

The ability of the machinery to reverse the direction of thrust of the propeller in sufficient time, and so to bring the ship to rest within a reasonable distance from maximum ahead service speed, shall be demonstrated and recorded.

.3

The stopping times, ship headings and distances recorded on trials, together with the results of trials to determine the ability of ships having multiple propellers to navigate and manoeuvre with one or more propellers inoperative, shall be available on board for use of the master or designated personnel.

.1

Every ship shall be provided with an efficient main and auxiliary steering system. The main steering system and the auxiliary steering system shall be so arranged that the failure of one of them will not render the other one inoperative.

.2

The main steering gear and rudder stock where fitted shall be:

.3

If fitted, the auxiliary steering gear shall be:

.4

Steering power units shall be:

.5

Where the main steering gear comprises two or more identical power units, an auxiliary steering gear need not be fitted, provided that:

.6

Steering gear control shall be provided:

.7

Any main and auxiliary steering gear control system operable from the navigating bridge shall comply with the following:

.8

The electrical power circuits and the steering gear control systems with their associated components, cables and pipes required by this regulation and by Regulation 7 shall be separated as far as is practicable throughout their length.

.9

A means of communication shall be provided between the navigating bridge and the steering gear compartment or alternative steering position.

.10

The angular position of the rudder(s) shall:

.11

Hydraulic power-operated steering gear shall be provided with the following:

.12

The steering gear compartments shall be:

.1

Means for indicating that the motors of electric and electro-hydraulic steering gears are running shall be installed on the navigating bridge and at a suitable main machinery control position.

.2

Each electric or electro-hydraulic steering system comprising one or more power units shall be served by at least two exclusive circuits fed directly from the main switchboard; however, one of the circuits may be supplied through the emergency switchboard. An auxiliary electric or electro-hydraulic steering system associated with a main electric or electro-hydraulic steering system may be connected to one of the circuits supplying this main steering system. The circuits supplying an electric or electro-hydraulic steering system shall have adequate rating for supplying all motors which can be simultaneously connected to them and may be required to operate simultaneously.

.1

Main and auxiliary machinery essential for the propulsion and the safety of the ship shall be provided with effective means for its operation and control.

.2

Where remote control of propulsion machinery from the navigating bridge is provided and the machinery spaces are intended to be manned, the following shall apply:

.3

Where the main propulsion and associated machinery, including sources of main electrical power supply, are provided with various degrees of automatic and remote control and are under continuous manual supervision from a control room the arrangements and controls shall be so designed, equipped and installed that the machinery operation will be as safe and effective as if it were under direct supervision; for this purpose Regulations II-1/E/1 to II-1/E/5 shall apply as appropriate. Particular consideration shall be given to protect such spaces against fire and flooding.

.4

In general, automatic starting, operational and control systems shall include provisions for manually overriding the automatic controls. Failure of any part of such systems shall not prevent the use of the manual override.

.5

The ships shall comply with the requirements of paragraphs .1 to .4.

.1

Every steam pipe and every fitting connected thereto through which steam may pass shall be so designed, constructed and installed as to withstand the maximum working stresses to which it may be subjected.

.2

Means shall be provided for draining every steam pipe in which dangerous water hammer action might otherwise occur.

.3

If a steam pipe or fitting may receive steam from any source at a higher pressure than that for which it is designed a suitable reducing valve, relief valve and pressure gauge shall be fitted.

.1

Means shall be provided to prevent overpressure in any part of compressed air systems and wherever water jackets or casings of air compressors and coolers might be subjected to dangerous overpressure due to leakage into them from air pressure parts. Suitable pressure relief arrangements shall be provided for all systems.

.2

The main starting air arrangements for main propulsion internal combustion engines shall be adequately protected against the effects of backfiring and internal explosion in the starting air pipes.

.3

All discharge pipes from starting air compressors shall lead directly to the starting air receivers, and all starting pipes from the air receivers to main and auxiliary engines shall be entirely separate from the compressor discharge pipe system.

.4

Provision shall be made to reduce to a minimum the entry of oil into the air pressure systems and to drain these systems.

.1

Passenger and goods lifts shall, in respect of dimensioning, layout, number of passengers and/or quantity of goods, comply with the provisions laid down by the Administration of the flag State in each individual case or for each type of plant.

.2

Installation drawings and maintenance instructions, including provisions governing periodical inspections, shall be approved by the Administration of the flag State, which shall inspect and approve the plant before it is taken into use.

.3

Following approval, the Administration of the flag State will issue a certificate which is to be kept on board.

.4

The Administration of the flag State may permit the periodical inspections to be carried out by an expert authorised by the Administration, or by a recognised organisation.

.1

Electrical installations shall be such that:

.2

The Administration of the flag State shall take appropriate steps to ensure uniformity of implementation and application of the provision of this part in respect of electrical installations (4).

.1

New ships of class C and D in which the electrical power is the only power for maintaining the auxiliary services essential for the safety of the ship, and new and existing ships of class B in which the electrical power is the only power for maintaining the auxiliary services essential for the safety and the propulsion of the ship, shall be provided with two or more main generating sets of such power that the aforesaid services can be operated when any one set is out of service.

In new class C and D ships of less than 24 metres in length, one of the main generating sets may be main propulsion engine-driven, provided it is of such power that the aforesaid services can be operated when any one other set is out of service.

.2.1

A main electric lighting system which shall provide illumination throughout those parts of the ship normally accessible to and used by passengers or crew shall be supplied from the main source of electrical power.

.2.2

The arrangement of the main electric lighting system shall be such that a fire or other casualty in spaces containing the main source of electrical power, associated transforming equipment, if any, the main switchboard and the main lighting switchboard, will not render the emergency lighting system, required by Regulation 3, inoperative.

.2.3

The arrangement of the emergency electric lighting system shall be such that a fire or other casualty in spaces containing the emergency source of electrical power, associated transforming equipment, if any, the emergency switchboard and the emergency lighting switchboard will not render the main electric lighting system required by this regulation inoperative.

.3

The main switchboard shall be so placed relative to one main generating station that, as far as is practicable, the integrity of the normal electrical supply may be affected only by a fire or other casualty in the space where the generating set and the switchboard are installed.

.1

be capable of operating in general for a period of:

.2

in particular, be capable to operate simultaneously the consumers as identified within the following services as required for the class of ships for the times indicated above:

.3

be capable to operate, for a period of half an hour, the power-operated watertight doors together with the associated control, indication and alarm circuits.

(a)

the lighting required by paragraph .2(b)1 of this regulation;

(b)

the watertight doors, as required by paragraphs .7.2 and .7.3 of Regulation II-1/B/13, but not necessarily all of them simultaneously, unless an independent temporary source of stored energy is provided; and

(c)

the control, indication and alarm circuits as required by paragraph .7.2 of Regulation II-1/B/13.

.1

all passenger public spaces and alleyways shall be provided with supplementary electric lighting that can operate for at least three hours when all other sources of electrical power have failed and under any condition of heel. The illumination provided shall be such that the approach to the means of escape can be readily seen. The source of power for the supplementary lighting shall consist of accumulator batteries located within the lighting units that are continuously charged, where practicable, from the emergency switchboard. Alternatively, any other means of lighting which is at least as effective may be accepted by the Administration of the flag State. The supplementary lighting shall be such that any failure of the lamp will be immediately apparent. Any accumulator battery provided shall be replaced at intervals having regard to the specific service life in the ambient conditions to which such batteries are subject when in service; and

.2

a portable rechargeable battery-operated lamp shall be provided in every crew space alleyway, recreational space and every working space which is normally occupied unless supplementary emergency lighting, as required by paragraph .1, is provided.

.1

Exposed metal parts of electrical machines or equipment which are not intended to be live but which are liable under fault conditions to become live shall be earthed unless the machines or equipment are:

.2

All electrical apparatus shall be so constructed and so installed as not to cause injury when handled or touched in the normal manner.

.3

The sides and the rear and, where necessary, the front of switchboards shall be suitably guarded. Exposed live parts having voltages to earth exceeding the voltage specified under 1.1 shall not be installed on the front of such switchboards. Where necessary, non-conducting mats or gratings shall be provided at the front and rear of the switchboard.

.4

In distribution systems with no connection to earth, a device capable of monitoring the insulation level to earth and giving an audible or visual indication of abnormally low insulation values shall be provided.

.5.1

All metal sheaths and armour of cables shall be electrically continuous and shall be earthed.

.5.2

All electrical cables and wiring external to equipment shall be at least of a flame-retarding type and shall be so installed as not to impair their original flame-retarding properties. Where necessary for a particular application, the Administration of the flag State may permit the use of special types of cables, such as radio frequency cables, which do not comply with the foregoing.

.5.3

Cables and wiring serving essential or emergency power, lighting, internal communications or signals shall so far as practicable be routed clear of galleys, laundries, machinery spaces of category A and their casings and other high fire risk areas. In new and existing ro-ro passenger ships, cabling for emergency alarms and public address systems installed on or after 1 July 1998 shall be approved by the Administration of the flag State having regard to the recommendations developed by the IMO. Cables connecting fire pumps to the emergency switchboard shall be of a fire-resistant type where they pass through high fire risk areas. Where practicable all such cables should be run in such a manner as to preclude their being rendered unserviceable by heating of the bulkheads that may be caused by a fire in an adjacent space.

.6

Cables and wiring shall be installed and supported in such a manner as to avoid chafing or other damage. Terminations and joints in all conductors shall be so made as to retain the original electrical, mechanical flame-retarding and, where necessary, fire resisting.

.7.1

Each separate circuit shall be protected against short circuit and against overload, except as permitted in Regulations II-1/C/6 and II-1/C/7.

.7.2

Lighting fittings shall be so arranged as to prevent temperature rises which could damage the cables and wiring, and to prevent surrounding material from becoming excessively hot.

.8.1

Accumulator batteries shall be suitably housed, and compartments used primarily for their accommodation shall be properly constructed and efficiently ventilated.

.8.2

Electrical or other equipment which may constitute a source of ignition of flammable vapours shall not be permitted in these compartments.

.9

Distribution systems shall be so arranged that fire in any main vertical zone, as defined in Regulation II-2/A/2.9, will not interfere with services essential for safety in any other such zone. This requirement will be met if main and emergency feeders passing through any such zone are separated both vertically and horizontally as widely as is practicable.

.1

The arrangements provided shall be such as to ensure that the safety of the ship in all sailing conditions, including manoeuvring, is equivalent to that of a ship having the machinery spaces manned.

.2

Measures shall be taken to ensure that the equipment is functioning in a reliable manner and that satisfactory arrangements are made for regular inspections and routine tests to ensure continuous reliable operation.

.3

Every ship shall be provided with documentary evidence of its fitness to operate with periodically unattended machinery spaces.

.1

Means shall be provided to detect and give alarms at an early stage in the event of fires:

.2

Internal combustion engines of 2 250 kW and above or having cylinders of more than 300 mm bore shall be provided with crankcase oil mist detectors or engine bearing temperature monitors or equivalent devices.

.1

Bilge wells in periodically unattended machinery spaces shall be located and monitored in such a way that the accumulation of liquids is detected at normal angles of trim and heel, and shall be large enough to accommodate easily the normal drainage during the unattended period.

.2

Where the bilge pumps are capable of being started automatically, means shall be provided to indicate when the influx of liquid is greater than the pump capacity or when the pump is operating more frequently than would normally be expected. In these cases, smaller bilge wells to cover a reasonable period of time may be permitted. Where automatically controlled bilge pumps are provided, special attention shall be given to oil pollution prevention requirements.

.3

The location of the controls of any valve serving a sea inlet, a discharge below the waterline or a bilge injection system shall be so sited as to allow adequate time for operation in the event of influx of water to the space, having regard to the time likely to be required in order to reach and operate such controls. If the level to which the space could become flooded with the ship in the fully loaded condition so requires, arrangements shall be made to operate the controls from a position above such level.

.1

Under all sailing conditions, including manoeuvring, the speed, direction of thrust and, if applicable, the pitch of the propeller shall be fully controllable from the navigating bridge.

.2

Propulsion machinery orders from the navigating bridge shall be indicated in the main machinery control room or at the propulsion machinery control position as appropriate.

.3

Remote control of the propulsion machinery shall be possible only from one location at a time; at such locations interconnected control positions are permitted. At each location there shall be an indicator showing which location is in control of the propulsion machinery. The transfer of control between the navigating bridge and machinery spaces shall be possible only in the main machinery space or in the main machinery control room. The system shall include means to prevent the propelling thrust from altering significantly when transferring control from one location to another.

.4

It shall be possible for all machinery essential for the safe operation of the ship to be controlled from a local position, even in the event of failure in any part of the automatic or remote control systems.

.5

The design of the remote automatic control system shall be such that in the event of its failure an alarm will be given. Unless it is considered impracticable, the preset speed and direction of thrust of the propeller shall be maintained until local control is in operation.

.6

Indicators shall be fitted on the navigating bridge for:

.7

The number of consecutive automatic attempts which fail to produce a start shall be limited to safeguard sufficient starting air pressure. An alarm shall be provided to indicate low starting air pressure set at a level which still permits starting operations of the propulsion machinery.

.1

An alarm system shall be provided indicating any fault requiring attention and shall:

.2.1

The alarm system shall be continuously powered and shall have an automatic changeover to a stand-by power supply in the event of loss of normal power supply.

.2.2

Failure of the normal power supply of the alarm system shall be indicated by an alarm.

.3.1

The alarm system shall be able to indicate at the same time more than one fault and the acceptance of any alarm shall not inhibit another alarm.

.3.2

Acceptance at the position referred to in paragraph .1 of any alarm condition shall be indicated at the positions where it was shown. Alarms shall be maintained until they are accepted and the visual indications of individual alarms shall remain until the fault has been corrected, when the alarm system shall automatically reset to the normal operating condition.

.1

The main source of electrical power shall comply with the following:

.2

Where stand-by machines are required for other auxiliary machinery essential to propulsion, automatic changeover devices shall be provided.

.1

The control system shall be such that the services needed for the operation of the main propulsion machinery and its auxiliaries are ensured through the necessary automatic arrangements.

.2

An alarm shall be given on the automatic changeover.

.3

An alarm system complying with Regulation 6 shall be provided for all important pressures, temperatures and fluid levels and other essential parameters.

.4

A centralised control position shall be arranged with the necessary alarm panels and instrumentation indicating any alarm.

.5

Means shall be provided to keep the starting air pressure at the required level where internal combustion engines essential for main propulsion are started by compressed air.

.1

The fire safety objectives of this chapter are to:

.2

In order to achieve the fire objectives set out in paragraph .1 the following basic principles underlie the regulations in this chapter and are embodied in the regulations as appropriate, having regard to the type of ships and the potential fire hazard involved:

.3

The fire safety objectives set out in paragraph .1 shall be achieved by ensuring compliance with the prescriptive requirements specified in this chapter or by alternative design and arrangements which comply with Part F of the revised Chapter II-2 of the 1974 SOLAS Convention, as amended, which applies to ships constructed on or after 1 January 2003. A ship shall be considered to meet the functional requirements set out in paragraph .2 and to achieve the fire safety objectives set out in paragraph .1 when either:

.4

All ships which undergo repairs, alterations, modifications and outfitting related thereto shall continue to comply with at least the requirements previously applicable to these ships.

Repairs, alterations and modifications which substantially alter the dimensions of a ship or the passenger accommodation spaces, or substantially increase a ship’s service life and outfitting related thereto shall meet the latest requirements for new ships in so far as the Administration of the flag State deems reasonable and practicable.

.5

Notwithstanding the provisions of paragraph .4, existing class B ships carrying more than 36 passengers when undergoing repairs, alterations, modifications and outfitting related thereto shall comply with the following:

.1

they shall be constructed of steel or other equivalent material;

.2

they shall be suitably stiffened;

.3

they shall be so constructed as to be capable of preventing the passage of smoke and flame to the end of the one-hour standard fire test;

.4

they shall be insulated with approved non-combustible materials such that the average temperature of the unexposed side will not rise more than 140 °C above the original temperature, nor will the temperature, at any one point, including any joint, rise more than 180 °C above the original temperature, within the time listed below:

.5

The Administration of the flag State shall require a test of a prototype bulkhead or deck to ensure that it meets the above requirements for integrity and temperature rise in accordance with the IMO Resolution A.754 (18).

For class B, C and D ships constructed on or after 1 January 2003, ‘IMO Resolution A.754 (18)’ shall read ‘Fire Test Procedures Code’.

.1

they shall be so constructed as to be capable of preventing the passage of flame to the end of the first half hour of the standard fire test;

.2

they shall have an insulation value such that the average temperature of the unexposed side will not rise more than 140 °C above the original temperature, nor will the temperature at any one point, including any joint, rise more than 225 °C above the original temperature within the time listed below:

.3

they shall be constructed of approved non-combustible materials and all materials entering into the construction and erection of ‘B’ class divisions shall be non-combustible, with the exception that combustible veneers may be permitted provided they meet other requirements of this chapter;

.4

the Administration of the flag State shall require a test of a prototype division to ensure that it meets the above requirements for integrity and temperature rise in accordance with IMO Resolution A.754 (18).

For class B, C and D ships constructed on or after 1 January 2003, ‘IMO Resolution 754 (18)’ shall read ‘Fire Test Procedures Code’.

.1

internal combustion machinery used for main propulsion; or

.2

internal combustion machinery used for purposes other than main propulsion where such machinery has in the aggregate a total power output of not less than 375 kW; or

.3

any oil-fired boiler or oil fuel unit.

.1

fixed fire detection and alarm systems;

.2

automatic sprinklers, fire detection and alarm systems;

.3

fire door indicator panels;

.4

fire doors closures;

.5

watertight door indicator panels;

.6

watertight door closures;

.7

ventilation fans;

.8

general/fire alarms;

.9

communication systems including telephones; and

.10

microphones to public address systems.

.1

all case furniture such as desks, wardrobes, dressing tables, bureaux, dressers, is constructed entirely of approved non-combustible materials, except that a combustible veneer not exceeding 2 mm may be used on the working surface of such articles;

.2

all free-standing furniture such as chairs, sofas, tables, is constructed with frames of non-combustible materials;

.3

all draperies, curtains and other suspended textile materials have qualities of resistance to the propagation of flame not inferior to those of wool of mass 0,8 kg/m2, in accordance with IMO Resolution A.471 (XII) and its amendments adopted by Resolution A.563 (14).

For class B, C and D ships constructed on or after 1 January 2003, ‘IMO Resolution A.471 (XII) and its amendments adopted by Resolution A.563 (14)’ shall read ‘Fire Test Procedures Code’;

.4

all floor coverings have qualities of resistance to the propagation of flame not inferior to those of an equivalent woollen material used for the same purpose.

For class B, C and D ships constructed on or after 1 January 2003, this subparagraph shall read:

‘all floor coverings have low flame spread characteristics’;